Can I Set Up a Bathtub Myself? Factors to Consider And Actions
Can I Set Up a Bathtub Myself? Factors to Consider And Actions
Blog Article
They are making a number of great observations on the subject of A Step-by-Step Guide to Installing a Bathtub in general in this great article below.
Setting up a bathtub isn't specifically rocket science, yet it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult task. If the old tub is conveniently accessible, the job can relocate rapidly; if you need to open a wall surface to eliminate the old bathtub and position the brand-new bathtub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. Rather than working with a contractor to take over a halfway-completed task, it is better to consider using one before you begin. Opportunities are you may need an expert plumber to make tube links.
This article will aid you install a new tub in your washroom if you have already gotten a brand-new bathtub and do not require to change the arrangement of your previous supply of water pipelines.
Your devices and material list need to consist of the following:
Preparing for the Setup
First of all, the sustaining structure provided with the bath should be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its last setting.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome due to the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly originate from the pipes. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before going on to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The following goal is to ensure that the tub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bathtub till the spirit level checks out level.
To set up faucets, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression join; then do the very same for the other faucet.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the tub must wait till the bathtub has actually been made use of at least once as this will certainly resolve it into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in area between the tap and the sink. Protect the tap in place with the maker given backnut. As soon as the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The former type ought to be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in problems with moisture and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack rather very early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily readily available on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were introduced to that report on How to Install a Bathtub through someone on our other web address. Are you aware of another person who is sincerely interested in the niche? Take a moment to share it. Kudos for your time. Come back soon.
Schedule Now!
Report this page